Multi-functional building waterproofing Combines the properties of flexible and crack-bridging mineral waterproofing grouts and bitumen thick coatings PMBC

is a surface-applied, integral crystalline waterproofing material, which waterproofs and protects concrete in-depth

special sealant for usages subject to high temperatures. up to 300°C
1 Carton (24piece)

Price per carton /20tubes
is a one-part polyurethane joint sealant suitable for horizontal and vertical use.

Single component, moisture cured, liquid Silicone roof coating

consists of Portland cement, specially treated quartz sand and a compound of active chemicals.

Single Component Water Based Hybrid Polyurethane Coating

(per 10Sheets) Rockwool Slab is a highly effective natural insulating material
minimum Quantity required 300 sheets

Size 600mm*1250mm Density (32-35)kg/cm3
price per board

(32-35KG/M3 Density)

High Performance Rubberized Bitumen Emulsion Coating

The RAK Green Building Regulation (Barjeel)
Supply and apply the approved quality waterproofing system for the roofs (Combo Roofing System).

1- Polyurethane foam, 60mm thick, and density of 40-45 kg/m³. ( UV 0.3 W/m²K ).
2- Acrylic - Liquid UV protection coat (600mic.Thick).
3- Geotextile /Separation Layer 100 g/m²
4- expansion separator material Fiberboard -at least 10 mm thick & no more than 16 square meters
5- Concrete screed (20N/M³ - 300 OPC, 80mm AVE. Thick.) without (Ice&Fibre)
6- Angle fillet (cement sand mortar ).
7- Remove the filler board/flexible sheet -stage (4).
8- Expansion joint filter (Backing rod and Pu sealant).
9- Acrylic Topcoat final

ROOF WATERPROOFING / SAB® MINERAL (MEMBRANE) SYSTEM:
1-One coat of bituminous primed surface.
2-One layer of APP Mineral Membrane 4mm thick 180 g/m2

Supply and apply the approved quality liquid waterproofing Cementitious system for all wet areas:-
1- Supply And Apply 2 coats of Cementitious Waterproofing.

SAB® Crystal 410 concentrate and one more other supporting material.
• As preparation:
• Cleaning scope of work area properly.
• Spraying the outer side with water, the Property of this material it needs wet area to make the required strong interaction.
• Puncture the surface by making tiny holes, this will ensure perfect absorption.
• Cleaning these small holes and insures it dry; taking into consideration the whole area is still wet.

1- Polyurethane foam spray 30-35mm
2- Acrylic top coat spray (LAITE GREEN)

Elastomeric Acrylic Waterproof & Protective Coating

per square meter
1mm-1.5mm Hand Applied, Rapid Curing Polyurea Waterproofing Membrane.

Supply and apply the approved quality system for pile head treatment and insulation 500 mm DIAMETER:-
1- Repair surface with cementitious grout
2- Treatment by using (Fosroc) super cast DC and super cast EP10

Two Component Polymer Modified Flexible Cementitious Waterproof Coating

is a state-of-the-art crystalline waterproofing admixture for concrete, available in powder form.

Apoc Incredible Heavy Duty Tape - The Ultimate DIY and Construction Tool

APP Modified bituminous membrane, reinforced with non woven polyester mat The polyester combines high tensile strength and elongation

Supply and apply of approved quality waterproofing system for all substructure concrete:
1 - One coat of cold Bituminous Primer
2 - Second coat of cold Bituminous Primer

High performance pile top fairing grout and cementitious void filler

ROOF WATERPROOFING / SAB® PRO 111 (MEMBRANE) SYSTEM:
1-Execute slope corners (skirting) 20cm*20cm along with the barbate.
2-Execute a Cavity 1.5*1.5 cm, along with the barbate over the skirting.
3-One coat of bituminous primed surface.
4-One layer of Membrane APP 4mm thick, 180 g/m2
5-Screed Concrete, 80mm Avg. 20/N - OPC 300 kg/m3
6-Execute slope corners 20cm*20cm along with the barbate.
7-Remove the ridges, then fill them with a sponge.
8-Supply and apply 1.5x1.5 cm mastic over the sponge.

is a two component acrylic copolymer based flexible cementitious waterproofing system

Concrete Smoothing

crystalline cementitious repair mortar designed specifically for concrete restoration